feat(bmc_tool : crashdump)添加手动执行crashdump脚本

1.补充usage，添加对新特性的描述
2.移除对channel name的校验，简化脚本

02.nicsensor/change_list.txt

@@ -1,9 +1,15 @@
-# Script Version 1.2
+# Script Version 1.3 20241229
+  Release Note
+    1.[新增功能]支持5280m7的OCP卡的使用
+    2.[新增功能]支持传感器tmp468和tmp112
+
+# Script Version 1.2 20241102
   Release Note:
     1.[新增功能]支持写入板卡FRU
-    2.[新增功能]添加适配服务器 donghu yichun
+    2.[新增功能]添加适配服务器 donghu yichun qiandaohu
     3.[功能优化]修复一些交互类bug,增强脚本健壮性
     4.[功能优化]更便捷的支持脚本传感器名称本地化
+    5.[功能优化]debug模式下执行i2c detect时可自定义执行detect内容
 
 # Script Version 1.1 20240912 
   Release Note:

02.nicsensor/code_structure.txt

@@ -0,0 +1,10 @@
+On Version V1.2
+    start_get_sensor //启动读取Sensor的流程
+        |--->set_configuration
+        |       |--->set_configuration_5280m7/5468m7/donghu/yichun //根据服务器类型设置具体I2C相关参数
+        |--->get_pca9641_controll //如果服务器上有PCA9641,选通它
+        |--->switch_pca9548_channel //切换9548/9546到对应的槽位上
+        |--->process_sensor
+                |--->sensor_init //传感器可能需要初始化 
+                |--->read_sensor_value //读取传感器的数值
+                |--->convert_sensor_value //处理传感器的读值并做可视化处理

02.nicsensor/plugin/adc128.sh

@@ -1,120 +0,0 @@
-#!/bin/sh
-
-log="/tmp/nicsensor_debug.log"
-
-INFO="Info"
-WARNING="Warning"
-ERROR="Error"
-
-votage_division_factor_0="1"
-votage_division_factor_1="1"
-votage_division_factor_2="1"
-votage_division_factor_3="0.8"
-votage_division_factor_4="0.6"
-votage_division_factor_5="0.6"
-votage_division_factor_6="0.2326"
-votage_division_factor_7="1"
-
-ADC128_Channel0_name="Channel 0"
-ADC128_Channel1_name="Channel 1"
-ADC128_Channel2_name="Channel 2"
-ADC128_Channel3_name="Channel 3"
-ADC128_Channel4_name="Channel 4"
-ADC128_Channel5_name="Channel 5"
-ADC128_Channel6_name="Channel 6"
-ADC128_Channel7_name="Channel 7"
-
-REG_adc128_config="0x00"
-REG_adc128_advance="0x0b"
-REG_adc128_status="0x0c"
-REG_adc128_ch0="0x20"
-REG_adc128_ch1="0x21"
-REG_adc128_ch2="0x22"
-REG_adc128_ch3="0x23"
-REG_adc128_ch4="0x24"
-REG_adc128_ch5="0x25"
-REG_adc128_ch6="0x26"
-REG_adc128_ch7="0x27"
-
-# 进行ADC128芯片的初始化
-check_adc128_init(){
-    # Get Reg 0x00 status
-    res_adc128_status=`i2cget -y $i2c_bus $chip_slave $REG_adc128_config`
-    format_log_print $INFO "REG adc128 STATUS : $res_adc128_status"
-
-    # if stauts is not 0x01 (Start Monitor) ,then do init
-    if [ "$res_adc128_status" != "0x01" ];then
-        format_log_print $INFO "Start Init ADC128 Chip"
-        # Init ADC128 work as mode 1 (0x02)
-        res_adc128_advance=`i2ctransfer -y $i2c_bus w2@$chip_slave $REG_adc128_advance 0x02`
-        # Set ADC128 on start (0x01)
-        res_adc128_setstart=`i2ctransfer -y $i2c_bus w2@$chip_slave $REG_adc128_config 0x01 r1`
-
-        format_log_print $INFO "After Set status, the REG 0x00 value is $res_adc128_setstart"
-    fi
-}
-
-# 处理ADC128读到的数据并输出结果
-# @Param 1 ADC128读取数据高位
-# @Param 2 ADC128读取数据低位
-# @Param 3 channel号/定制化名称
-# @Param 4 分压系数
-convert_adc128_data(){
-    # 将读取到的两位数据拼接起来
-    hex_value1=$(echo "$1" | awk '{sub(/^0x/,""); print}')
-    hex_value2=$(echo "$2" | awk '{sub(/^0x/,""); print}')
-    merge_value="${hex_value1}${hex_value2}"
-
-    # 由于 bc 计算器只能识别大写的 十六进制数据，这里将小写的十六进制数据全部转化为大写的数据
-    upper_hex_value=$(echo "$merge_value" | awk '{ 
-        for(i=1; i<=length($0); i++){ 
-            if(tolower(substr($0,i,1)) ~ /^[a-f]$/) 
-                printf toupper(substr($0,i,1)); 
-            else 
-                printf substr($0,i,1); 
-        } 
-        print "" 
-    }')
-
-    # 利用bc计算器进行运算，并将返回值格式化后输出
-    dec_val=$(echo "ibase=16; $upper_hex_value" | bc)
-    volt=$(echo "scale=4; $dec_val / 16 / 4096 * 2.65 / $4" | bc)
-    format_volt=$(echo "$volt" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-
-    echo "$3 : $format_volt v, hex value: $upper_hex_value"
-}
-
-# 读取ADC128芯片每个通道的数据,随后调用数据处理函数进行数据解析并输出
-read_adc128_channel_value(){
-    format_log_print $INFO "Start Read ADC128 channel data ..."
-
-    res_ch0=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch0 r2`
-    res_ch1=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch1 r2`
-    res_ch2=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch2 r2`
-    res_ch3=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch3 r2`
-    res_ch4=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch4 r2`
-    res_ch5=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch5 r2`
-    res_ch6=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch6 r2`
-    res_ch7=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_adc128_ch7 r2`
-
-    # 将 I2C 读取的 raw 数据记录到调试日志中
-    format_log_print $INFO "channel0 : $res_ch0"
-    format_log_print $INFO "channel1 : $res_ch1"
-    format_log_print $INFO "channel2 : $res_ch2"
-    format_log_print $INFO "channel3 : $res_ch3"
-    format_log_print $INFO "channel4 : $res_ch4"
-    format_log_print $INFO "channel5 : $res_ch5"
-    format_log_print $INFO "channel6 : $res_ch6"
-    format_log_print $INFO "channel7 : $res_ch7"
-
-    # start parse raw data
-    echo ">>> The ADC128 value is :"
-    convert_adc128_data $res_ch0 $ADC128_Channel0_name $votage_division_factor_0
-    convert_adc128_data $res_ch1 $ADC128_Channel1_name $votage_division_factor_1
-    convert_adc128_data $res_ch2 $ADC128_Channel2_name $votage_division_factor_2
-    convert_adc128_data $res_ch3 $ADC128_Channel3_name $votage_division_factor_3
-    convert_adc128_data $res_ch4 $ADC128_Channel4_name $votage_division_factor_4
-    convert_adc128_data $res_ch5 $ADC128_Channel5_name $votage_division_factor_5
-    convert_adc128_data $res_ch6 $ADC128_Channel6_name $votage_division_factor_6
-    convert_adc128_data $res_ch7 $ADC128_Channel7_name $votage_division_factor_7
-}

02.nicsensor/plugin/chip.sh

@@ -1,18 +0,0 @@
-#!/bin/sh
-
-log="/tmp/nicsensor_debug.log"
-
-INFO="Info"
-WARNING="Warning"
-ERROR="Error"
-
-# 临时支持CHIP读取寄存器
-write_read_chip(){
-    
-    # Modify i2c cmd which write to cpld if need
-    cmd_wr=$option_data
-    res_wr=`$cmd_wr`
-
-    format_print $INFO ">>> Chip Command: $cmd_wr"
-    format_print $INFO ">>> The Result  : $res_wr"
-}

02.nicsensor/plugin/detect.sh

@@ -1,183 +0,0 @@
-#!/bin/sh
-
-log="/tmp/nicsensor_debug.log"
-
-INFO="Info"
-WARNING="Warning"
-ERROR="Error"
-
-# 在 5280m7 上扫描每个pcie slot下的I2C设备
-# 详细对应关系参阅 readme.txt 第二节
-detect_on_5280m7(){
-    # 从9641获取I2C控制权
-    i2c_bus=12
-    pca9641_slave="0x41"
-    get_pca9641_controll
-
-    format_print $INFO "PCIe slot 0 : bus12 9548channel 1"
-    i2ctransfer -y $i2c_bus w1@0x72 0x02
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 1 : bus12 9548channel 2"
-    i2ctransfer -y $i2c_bus w1@0x72 0x04
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 2 : bus12 9548channel 3"
-    i2ctransfer -y $i2c_bus w1@0x72 0x08
-    i2cdetect -y $i2c_bus
-
-    i2c_bus=13
-    pca9641_slave="0x42"
-    get_pca9641_controll
-    
-    format_print $INFO "PCIe slot 3 : bus13 9548channel 1"
-    i2ctransfer -y $i2c_bus w1@0x72 0x02
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 4 : bus13 9548channel 2"
-    i2ctransfer -y $i2c_bus w1@0x72 0x04
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 5 : bus13 9548channel 3"
-    i2ctransfer -y $i2c_bus w1@0x72 0x08
-    i2cdetect -y $i2c_bus
-}
-
-# 在 5468m7 上扫描每个pcie slot下的I2C设备
-# 详细对应关系参阅 readme.txt 第二节
-detect_on_5468m7(){
-    # 从9641获取I2C控制权
-    i2c_bus=13
-    pca9641_slave="0x31"
-    get_pca9641_controll
-
-    format_print $INFO "PCIe slot 0 : bus13 9548channel 0"
-    i2ctransfer -y $i2c_bus w1@0x70 0x01
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 1 : bus13 9548channel 1"
-    i2ctransfer -y $i2c_bus w1@0x70 0x02
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 2 : bus13 9548channel 2"
-    i2ctransfer -y $i2c_bus w1@0x70 0x04
-    i2cdetect -y $i2c_bus
-    
-    format_print $INFO "PCIe slot 3 : bus13 9548channel 3"
-    i2ctransfer -y $i2c_bus w1@0x70 0x08
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 4 : bus13 9548channel 4"
-    i2ctransfer -y $i2c_bus w1@0x70 0x10
-    i2cdetect -y $i2c_bus
-
-    i2c_bus=14
-    pca9641_slave="0x42"
-    get_pca9641_controll
-
-    format_print $INFO "PCIe slot 5 : bus14 9548channel 0"
-    i2ctransfer -y $i2c_bus w1@0x71 0x01
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 6 : bus14 9548channel 1"
-    i2ctransfer -y $i2c_bus w1@0x71 0x02
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 7 : bus14 9548channel 2"
-    i2ctransfer -y $i2c_bus w1@0x71 0x04
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 8 : bus14 9548channel 3"
-    i2ctransfer -y $i2c_bus w1@0x71 0x08
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 9 : bus14 9548channel 4"
-    i2ctransfer -y $i2c_bus w1@0x71 0x10
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 10 : bus14 9548channel 5"
-    i2ctransfer -y $i2c_bus w1@0x71 0x20
-    i2cdetect -y $i2c_bus
-}
-
-# 在 donghu 上扫描每个pcie slot下的I2C设备
-detect_on_donghu(){
-
-    i2c_bus=3
-
-    format_print $INFO "PCIe slot 0 : bus3 9548channel 7"
-    i2ctransfer -y $i2c_bus w1@0x70 0x80
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 1 : bus3 9548channel 6"
-    i2ctransfer -y $i2c_bus w1@0x70 0x40
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 2 : bus3 9548channel 5"
-    i2ctransfer -y $i2c_bus w1@0x70 0x20
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 3 : bus3 9548channel 4"
-    i2ctransfer -y $i2c_bus w1@0x70 0x10
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 4 : bus3 9548channel 3"
-    i2ctransfer -y $i2c_bus w1@0x70 0x08
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 5 : bus3 9548channel 2"
-    i2ctransfer -y $i2c_bus w1@0x70 0x04
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 6 : bus3 9548channel 1"
-    i2ctransfer -y $i2c_bus w1@0x70 0x02
-    i2cdetect -y $i2c_bus
-
-    format_print $INFO "PCIe slot 7 : bus3 9548channel 0"
-    i2ctransfer -y $i2c_bus w1@0x70 0x01
-    i2cdetect -y $i2c_bus
-}
-
-# 在 yichun 上扫描每个pcie slot下的I2C设备
-detect_on_yichun(){
-    i2c_bus=12
-    format_print $INFO "PCIe slot 0 : bus12 9546channel 2"
-    i2ctransfer -y $i2c_bus w1@0x74 0x02
-    i2cdetect -y $i2c_bus
-
-    i2c_bus=13
-    format_print $INFO "PCIe slot 1 : bus13 9546channel 2"
-    i2ctransfer -y $i2c_bus w1@0x74 0x02
-    i2cdetect -y $i2c_bus
-
-    i2c_bus=14
-    format_print $INFO "PCIe slot 2 : bus14 9546channel 2"
-    i2ctransfer -y $i2c_bus w1@0x74 0x02
-    i2cdetect -y $i2c_bus
-}
-
-# 搜索服务器所有PCIE插槽的I2C设备信息,当前仅支持特定Riser卡上的设备
-# change list : 20240912-支持服务器器型号5280m7,5468m7
-start_detect_device(){
-
-    # debug mode下进行detect操作仅对当前链路进行detect
-    if [ $DEBUG_MODE -ne 0 ];then
-        format_print $INFO "In debug mode now, only detect i2c_bus$i2c_bus:"
-        i2cdetect -y $i2c_bus
-        exit 0
-    fi
-
-    format_print $INFO "Detect on server : $server_type"
-
-    if [ $server_type == "5280m7" ];then
-        detect_on_5280m7
-    elif [ $server_type == "5468m7" ];then
-        detect_on_5468m7
-    elif [ $server_type == "donghu" ];then
-        detect_on_donghu
-    elif [ $server_type == "yichun" ];then
-        detect_on_yichun
-    else
-        format_print $ERROR "Unsupport Server Type !!!"
-    fi
-}

02.nicsensor/plugin/emc1413.sh

@@ -1,86 +0,0 @@
-#!/bin/sh
-
-log="/tmp/nicsensor_debug.log"
-
-INFO="Info"
-WARNING="Warning"
-ERROR="Error"
-
-EMC1413_Channel0_name="Channel 0"
-EMC1413_Channel1_name="Channel 1"
-EMC1413_Channel2_name="Channel 2"
-
-REG_emc1413_TD1_H="0x00"
-REG_emc1413_TD1_L="0x29"
-REG_emc1413_TD2_H="0x01"
-REG_emc1413_TD2_L="0x10"
-REG_emc1413_TD3_H="0x23"
-REG_emc1413_TD3_L="0x24"
-
-# 处理EMC1413读到的数据并输出结果
-# @Param1 emc1413读取数据高位
-# @Param2 emc1413读取数据低位
-# @Param3 channel号/定制化名称
-convert_emc1413_data(){
-    # 将读取到的两位数据去掉 0x 前缀
-    hex_value1=$(echo "$1" | awk '{sub(/^0x/,""); print}')
-    hex_value2=$(echo "$2" | awk '{sub(/^0x/,""); print}')
-
-    # 由于 bc 计算器只能识别大写的 十六进制数据，将小写的十六进制数据全部转化为大写的数据
-    upper_hex_value1=$(echo "$hex_value1" | awk '{ 
-        for(i=1; i<=length($0); i++){ 
-            if(tolower(substr($0,i,1)) ~ /^[a-f]$/) 
-                printf toupper(substr($0,i,1)); 
-            else 
-                printf substr($0,i,1); 
-        } 
-        print "" 
-    }')
-    upper_hex_value2=$(echo "$hex_value2" | awk '{ 
-        for(i=1; i<=length($0); i++){ 
-            if(tolower(substr($0,i,1)) ~ /^[a-f]$/) 
-                printf toupper(substr($0,i,1)); 
-            else 
-                printf substr($0,i,1); 
-        } 
-        print "" 
-    }')
-
-    # 转化为10进制数据
-    dec_value1=$(echo "ibase=16; $upper_hex_value1" | bc)
-    dec_value2=$(echo "ibase=16; $upper_hex_value2" | bc)
-
-    # 计算温度值
-    temp=$(echo "scale=4; $dec_value1 + ($dec_value2 / 32 * 0.125 )" | bc)
-
-    # 格式化输出数据
-    format_temp=$(echo "$temp" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-
-    echo "$3 : $format_temp C, hex value : $hex_value1 $hex_value2"
-
-}
-
-# 读取EMC1413芯片每个通道的数据,随后调用数据处理函数进行数据解析并输出
-read_emc1413_channel_value(){
-
-    format_log_print $INFO "Start EMC1413 channel data ..."
-
-    res_td1_h=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_emc1413_TD1_H r1`
-    res_td1_l=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_emc1413_TD1_L r1`
-    res_td2_h=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_emc1413_TD2_H r1`
-    res_td2_l=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_emc1413_TD2_L r1`
-    res_td3_h=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_emc1413_TD3_H r1`
-    res_td3_l=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_emc1413_TD3_L r1`
-
-    # 将 I2C 读取的 raw 数据记录到调试日志中
-    format_log_print $INFO "channel 1 : $res_td1_h $res_td1_l"
-    format_log_print $INFO "channel 2 : $res_td2_h $res_td2_l"
-    format_log_print $INFO "channel 3 : $res_td3_h $res_td3_l"
-
-    # start parse raw data
-    echo ">>> The emc1413 value is:"
-    convert_emc1413_data $res_td1_h $res_td1_l $EMC1413_Channel0_name 
-    convert_emc1413_data $res_td2_h $res_td2_l $EMC1413_Channel1_name
-    convert_emc1413_data $res_td3_h $res_td3_l $EMC1413_Channel2_name
-
-}

02.nicsensor/plugin/fru.sh

@@ -1,92 +0,0 @@
-#!/bin/sh
-
-log="/tmp/nicsensor_debug.log"
-
-INFO="Info"
-WARNING="Warning"
-ERROR="Error"
-
-# fru 烧录的起始地址
-fru_offset="0x00 0x00"
-
-fru_write_size=0
-fru_write_data=""
-
-# 将传入的fru文件解析为可被i2cransfer直接写入的数据
-parse_fru_write_data(){
-    # 判断fru文件是否存在于当前目录
-    if [ -e $fru_file_name ];then
-        format_log_print $INFO "Fru file exist!"
-    else
-        format_log_print $ERROR "Fru file not exist!"
-        format_print $WARNING "Fru file not exist in current directory!"
-        format_print $ERROR "Operation Failed!"
-        exit 1
-    fi
-    
-    # 计算需要写入的fru文件大小
-    fru_write_size=`ls -lht | grep $fru_file_name | awk '{print $5}'`
-    format_print $INFO "Fru File [$fru_file_name] size = $fru_write_size Bytes"
-    format_log_print $INFO "Fru File [$fru_file_name] size = $fru_write_size Bytes"
-
-    # 获取fru文件的 raw data
-    fru_raw_data=`hexdump -C $fru_file_name | awk '{
-        for(i=2;i<18;i++){
-            print $i
-        }
-    }'`
-    format_log_print $INFO "Fru Raw Data: $fru_raw_data"
-
-    # 将raw data解析为可被 i2ctransfer 写入的数据
-    fru_write_data=`echo $fru_raw_data | awk -v size=$fru_write_size '{
-        for(i=1;i<=size;i++){
-            printf "0x%s ",$i
-        }
-    }'`
-}
-
-# 支持FRU读取
-read_fru(){
-
-    res_fru=`i2ctransfer -y $i2c_bus w2@$chip_slave $fru_offset r256`
-
-    # 将FRU数据按照每行16个字符输出
-    echo "The Fru Data :"
-    echo "$res_fru" | \
-    awk '{
-        line="";
-        count=0;
-
-        for(i=1; i<=NF; i++){
-            hex=substr($i, 3);
-
-            if(line != ""){
-                line = line " ";
-            }
-            line = line hex;
-
-            count++;
-            if (count == 16){
-                print line;
-                line = "";
-                count = 0;
-            }
-        }
-
-        if(line != ""){
-            print line;
-        }
-    }'
-
-}
-
-# 20240926 支持写板卡FRU
-write_fru(){
-    
-    i2c_write_byte=$(($fru_write_size+2))
-    # 组装command并发送
-    write_command="i2ctransfer -y $i2c_bus w$i2c_write_byte@$chip_slave $fru_offset $fru_write_data"
-    write_res=`$write_command`
-    format_log_print $INFO "Exec Command: $write_command"
-
-}

02.nicsensor/plugin/ina3221.sh

@@ -1,155 +0,0 @@
-#!/bin/sh
-
-log="/tmp/nicsensor_debug.log"
-
-INFO="Info"
-WARNING="Warning"
-ERROR="Error"
-
-shunt_resistor_0="2"
-shunt_resistor_1="2"
-shunt_resistor_2="5"
-
-REG_ina3221_ch1="0x01"
-REG_ina3221_ch2="0x03"
-REG_ina3221_ch3="0x05"
-REG_ina3221_bus1="0x02"
-REG_ina3221_bus2="0x04"
-REG_ina3221_bus3="0x06"
-
-INA3221_SHUNT_VOLT=0
-INA3221_BUS_VOLT=1
-INA3221_POWER=2
-
-ina3221_ch0_volt="0"
-ina3221_ch1_volt="0"
-ina3221_ch2_volt="0"
-ina3221_ch0_current="0"
-ina3221_ch1_current="0"
-ina3221_ch2_current="0"
-
-# 处理INA3221读到的电流数据并输出结果
-# @Param1 ina3221读取数据高位
-# @Param2 ina3221读取数据低位
-# @Param3 channel号
-# @Param4 0代表数据是shunt volt
-#         1代表数据是bus volt
-# @Param5 分流电阻 (仅在 Param4 是 shunt volt时有用)
-convert_ina3221_data(){
-    # 将读取到的两位数据拼接起来
-    hex_value1=$(echo "$1" | awk '{sub(/^0x/,""); print}')
-    hex_value2=$(echo "$2" | awk '{sub(/^0x/,""); print}')
-    merge_value="${hex_value1}${hex_value2}"
-
-    # 由于 bc 计算器只能识别大写的 十六进制数据，这里将小写的十六进制数据全部转化为大写的数据
-    upper_hex_value=$(echo "$merge_value" | awk '{ 
-        for(i=1; i<=length($0); i++){ 
-            if(tolower(substr($0,i,1)) ~ /^[a-f]$/) 
-                printf toupper(substr($0,i,1)); 
-            else 
-                printf substr($0,i,1); 
-        } 
-        print "" 
-    }')
-
-    # 将16进制数据转化为10进制
-    dec_val=$(echo "ibase=16; $upper_hex_value" | bc)
-
-    # todo 检查这个数据的最高位是否为1
-    # max_unsigned_32bit_half=$(echo "scale=0; 2^31 / 2" | bc)
-    # if [ $(echo "$dec_val >= $max_unsigned_32bit_half" | bc) -eq 1 ];then
-    #     echo ""
-    # else
-    #     echo ""
-    # fi
-    if [ $4 -eq $INA3221_BUS_VOLT ];then
-        # 计算每个通道上的电压
-        volt=$(echo "scale=4; $dec_val / 8 * 40 / 10000 * 2" | bc)
-
-        # 格式化输出数据
-        format_volt=$(echo "$volt" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-
-        echo "channel $3 : $format_volt V, hex value: $upper_hex_value"
-
-        if [ $3 -eq 0 ];then
-            ina3221_ch0_volt=$format_volt
-        elif [ $3 -eq 1 ];then
-            ina3221_ch1_volt=$format_volt
-        else
-            ina3221_ch2_volt=$format_volt
-        fi
-
-    elif [ $4 -eq $INA3221_SHUNT_VOLT ];then
-        # 计算每个分流电阻上的电压，同时计算出电流
-        current_mv=$(echo "scale=4; $dec_val / 8 * 40 / 1000" | bc)
-        current=$(echo "scale=4; $current_mv / $5" | bc)
-
-        # 格式化输出数据
-        format_current=$(echo "$current" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-        format_current_mv=$(echo "$current_mv" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-
-        echo "channel $3 : $format_current A, shunt volt: $format_current_mv mV, shunt resistor: $5 mOhm, hex value: $upper_hex_value"
-
-        if [ $3 -eq 0 ];then
-            ina3221_ch0_current=$format_current
-        elif [ $3 -eq 1 ];then
-            ina3221_ch1_current=$format_current
-        else
-            ina3221_ch2_current=$format_current
-        fi
-
-    elif [ $4 -eq $INA3221_POWER ];then
-        # 计算每个通道上的功耗，并算总和
-        power_ch0=$(echo "scale=4; $ina3221_ch0_volt * $ina3221_ch0_current" | bc)
-        power_ch1=$(echo "scale=4; $ina3221_ch1_volt * $ina3221_ch1_current" | bc)
-        power_ch2=$(echo "scale=4; $ina3221_ch2_volt * $ina3221_ch2_current" | bc)
-
-        # 格式化输出数据
-        format_power_ch0=$(echo "$power_ch0" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-        format_power_ch1=$(echo "$power_ch1" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-        format_power_ch2=$(echo "$power_ch2" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
-
-        total_power=$(echo "scale=4; $power_ch0 + $power_ch1 + $power_ch2" | bc)
-
-        echo "channel 0  : $format_power_ch0 W"
-        echo "channel 1  : $format_power_ch1 W"
-        echo "channel 2  : $format_power_ch2 W"
-        echo "total power: $total_power W"
-    fi
-}
-
-# 读取INA3221芯片每个通道的数据,随后调用数据处理函数进行数据解析并输出
-read_ina3221_channel_value(){
-    format_log_print $INFO "Start Read INA3221 channel data ..."
-
-    res_ch0=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_ina3221_ch1 r2`
-    res_ch1=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_ina3221_ch2 r2`
-    res_ch2=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_ina3221_ch3 r2`
-    res_bus0=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_ina3221_bus1 r2`
-    res_bus1=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_ina3221_bus2 r2`
-    res_bus2=`i2ctransfer -y $i2c_bus w1@$chip_slave $REG_ina3221_bus3 r2`
-    
-
-    # 将 I2C 读取的 raw 数据记录到调试日志中
-    format_log_print $INFO "channel 0 shunt volt: $res_ch0" 
-    format_log_print $INFO "channel 1 shunt volt: $res_ch1"
-    format_log_print $INFO "channel 2 shunt volt: $res_ch2"
-
-    format_log_print $INFO "Channel 0 bus volt : $res_bus0"
-    format_log_print $INFO "Channel 1 bus volt : $res_bus1"
-    format_log_print $INFO "Channel 2 bus volt : $res_bus2"
-
-    # start parse raw data
-    echo ">>> The INA3221 shunt value is :"
-    convert_ina3221_data $res_ch0 0 $INA3221_SHUNT_VOLT $shunt_resistor_0
-    convert_ina3221_data $res_ch1 1 $INA3221_SHUNT_VOLT $shunt_resistor_1
-    convert_ina3221_data $res_ch2 2 $INA3221_SHUNT_VOLT $shunt_resistor_2
-
-    echo ">>> The INA3221 bus value is :"
-    convert_ina3221_data $res_bus0 0 $INA3221_BUS_VOLT 
-    convert_ina3221_data $res_bus1 1 $INA3221_BUS_VOLT 
-    convert_ina3221_data $res_bus2 2 $INA3221_BUS_VOLT 
-
-    echo ">>> The INA3221 bus power is :"
-    convert_ina3221_data 0 0 0 $INA3221_POWER
-}

02.nicsensor/readme.md

@@ -0,0 +1,4 @@
+# 文件更新
+
+当前不在继续维护
+继续更新详见 [nicsensor](http://121.36.59.21:3000/Marcin/nicsensor)

02.nicsensor/readme.txt

@@ -1,138 +0,0 @@
-    ### 重要说明 : 脚本仅用于M7服务器，带有i2c standard tool工具的BMC使用
-    ### 仅限用于实验室调试使用
-
-    ### 大纲
-        一、脚本使用方法
-            1.1 修改项目专属配置(必做)
-            1.2 增加脚本可执行权限
-            1.3 脚本命令格式
-            1.4 特殊命令
-                1.4.1 Detect命令
-                1.4.2 fru命令
-                1.4.3 读取芯片寄存器
-            1.5 debug模式
-        二、服务器PCIE槽位和PCA9548的channel关系
-        三、M7 sysadmin用户 SSH打开方法
-        四、常见问题
-
-    ### 正文
-    
-    一、脚本使用方法 Version1.2
-
-        1.1、修改项目专属配置
-            针对不同项目，请先修改脚本中的部分变量(ADC128电压传感器的分压系数,INA3221的分流精密电阻阻值)
-            针对不同服务器产品,请对应修改server_type变量, 当前支持设置的服务器型号：
-                5280m7
-                5468m7
-                donghu
-
-        1.2、增加脚本可执行权限 
-            
-            在脚本目录下执行命令: chmod +x ./nicsensor.sh 
-
-        1.3、脚本命令格式 
-            
-            ./nicsensor.sh <pcie_slot> <chip_type> <chip_slave>
-            
-            参数说明:
-                pcie_slot : 网卡所在的PCIE槽位, 填数字0,1,2,3,4,5
-                chip_type : 传感器芯片的类型, emc1413,adc128,ina3221
-                chip_slave: 传感器芯片的I2C地址(7bit)
-            
-            举例说明:读取PCIE 1 上网卡的adc128芯片, 芯片slave地址为0x1f
-                ./nicsensor.sh 1 adc128 0x1f
-
-        1.4、特殊命令
-
-            1.4.1 Detect命令
-                
-                扫描服务器的PCIE slot 0 - 5上所有的I2C设备
-
-                命令: ./nicsensor.sh detect
-            
-            1.4.2 fru命令
-
-                命令: ./nicsensor.sh <pcie_slot> fru <chip_slave> read
-                举例说明:读取Ravel板卡的EEPROM中的FRU(0x57)
-                    - ./nicsensor.sh 5 fru 0x57 read
-
-            1.4.3 读取芯片寄存器
-
-                命令: ./nicsensor.sh <pcie_slot> chip <chip_slave> <i2c_cmd>
-                举例说明: 读取cpld的寄存器 0x00 ,读2个byte 
-                    - ./nicsensor.sh 5 chip 0x10 "i2ctransfer -y 13 w1@0x10 0x00 r2"
-        
-        1.5、DEBUG模式
-
-            可通过配置脚本中的 DEBUG_MODE 变量(In Srcipt Line:112)来使用debug模式,在debug模式下,不会执行选通
-            9641,9548的操作,仅执行读取传感器的操作,因此启用debug模式后需要手动配置的变量有:
-                i2c_bus
-
-
-    二、服务器PCIE槽位和PCA9548的channel关系
-
-        5280M7的PCIE槽位和PCA9548/9546没有确定的对应关系,取决于使用的riser卡.根据一般情况选择的Riser卡, 对应
-        情况如下:
-
-            PCIE 0 = i2c bus 12 , 9548channel1(0x02)
-            PCIE 1 = i2c bus 12 , 9548channel2(0x04)
-            PCIE 2 = i2c bus 12 , 9548channel3(0x08)
-            PCIE 3 = i2c bus 13 , 9548channel1(0x02)
-            PCIE 4 = i2c bus 13 , 9548channel2(0x04)
-            PCIE 5 = i2c bus 13 , 9548channel3(0x08)
-        
-        5468M7的PCIE槽位和PCA9548/9546的对应关系:
-
-            PCIE 0  = i2c bus 13 , 9548channel0(0x01)
-            PCIE 1  = i2c bus 13 , 9548channel1(0x02)
-            PCIE 2  = i2c bus 13 , 9548channel2(0x04)
-            PCIE 3  = i2c bus 13 , 9548channel3(0x08)
-            PCIE 4  = i2c bus 13 , 9548channel4(0x10)
-            PCIE 5  = i2c bus 14 , 9548channel0(0x01)
-            PCIE 6  = i2c bus 14 , 9548channel1(0x02)
-            PCIE 7  = i2c bus 14 , 9548channel2(0x04)
-            PCIE 8  = i2c bus 14 , 9548channel3(0x08)
-            PCIE 9  = i2c bus 14 , 9548channel4(0x10)
-            PCIE 10 = i2c bus 14 , 9548channel5(0x20)
-
-        针对不同服务器产品,请对应修改server_type变量,当前支持的服务器类型:
-            5280m7
-            5468m7
-    
-    三、M7 sysadmin用户 SSH打开方法
-
-        5280M7服务器默认不开启SSH, 且串口通常有较多干扰打印, 因此推荐使用SSH来执行脚本, 刷新BMC镜像后需要重新配置
-
-        1、打开M7 BMC的串口, 可通过串口线或者IPMI SOL带外登入
-
-            使用IPMI SOL的前提环境: 可与BMC网络连接, 且电脑上有ipmitool工具
-            SOL登陆方法:
-                (1) 将SOL串口源切换到BMC:
-                    ipmitool -I lanplus -H <bmcip> -U admin -P admin raw 0x3c 0x2c 0x02 0x01
-                (2) 打开SOL:
-                    ipmitool -I lanplus -H <bmcip> -U admin -P admin sol activate
-                备注: <bmcip> 为目标BMC的ip地址, 请自行更改为对应的ip地址
-
-        2、登录进入bmc的linux系统
-
-            bmc linux系统的默认用户名/密码 : sysadmin/superuser
-        
-        3、在BMC的linux系统下执行命令
-
-            (1) cp /etc/defconfig/ssh_server_config_with_sysadmin /etc/ssh/sshd_config
-            
-            (2) /etc/init.d/ssh restart
-
-            执行完毕后，就可以使用ssh登录BMC了
-
-    四、常见问题
-
-        1、脚本执行时出现大量的 Error
-
-            由于M7服务器的I2C设计有PCA9641作为I2C仲裁器, 脚本执行过程中可能会被9641强行断开I2C连接, 造成大量的
-            脚本Error, 这种情况在实际运行中是不可避免的, 直接重新执行脚本即可
-
-        2、不建议使用该脚本进行压力测试
-
-            由于BMC shell的版本非常原始, 没有集成高级的命令行工具, 因此处理数值时采用了复杂的脚本逻辑进行执行, 处
-            理效率较低。另外由于9641芯片的存在, 不能保证压力测试的正常执行。

05.auto_work/obsidian_pull.bat

@@ -0,0 +1,9 @@
+@echo off
+::配置Obsidian workspace地址
+set obsidian_path="D:\Files\3.SelfLerning\Marcin's_Repo"
+::切换目录到 Obsidian workspace下
+D:
+cd %obsidian_path%
+
+::先拉取远端更新
+git pull

05.auto_work/obsidian_push.bat

@@ -0,0 +1,20 @@
+@echo off
+::配置Obsidian workspace地址
+set obsidian_path="D:\Files\3.SelfLerning\Marcin's_Repo"
+::切换目录到 Obsidian workspace下
+D:
+cd %obsidian_path%
+
+::判断是否有更新并将更新同步到远端仓库
+for /f "delims=" %%a in ('git status --porcelain') do (
+    set HAS_CHANGES=1
+    goto end_loop
+)
+:end_loop
+if defined HAS_CHANGES (
+    git add -A
+    git commit -m "Daily Sync from workbook"
+    git push origin main
+) else (
+    echo Git has no changes.
+)

07.bmc_tool_script/Linux_CollectOnekeylog.sh

@@ -0,0 +1,38 @@
+#!/bin/bash
+
+BMC_IP=$1
+BMC_USER=$2
+BMC_PW=$3
+BMC_INFO="${BMC_USER}:${BMC_PW}"
+
+if [ $# -lt 3 ];then
+    echo "Script Usage:"
+    echo "    ./Outband_Collect_OneKeyLog.sh <BMC_IP> <BMC_USERNAME> <BMC_PASSWORD>"
+    exit 0
+fi
+
+# Get BoardSN
+BoardSN=`ipmitool -H ${BMC_IP} -I lanplus -U ${BMC_USER} -P ${BMC_PW} fru print | grep "Board Serial" | awk '{print $4}'`
+
+if [ "${BoardSN}" = "" ];then
+    echo "Error: Can't Get BoardSN, please check network connection or user&password !"
+    exit 1
+fi
+
+time=`date "+%Y-%m-%dT%H:%M:%S"`
+LOG_FILENAME="Product_${BoardSN}_${time}.tar.gz"
+
+# Post message to BMC to collect all log
+echo -e "\n Step 1. Post Collect all log to BMC"
+curl -k -u $BMC_INFO -X POST -H "Content-Length: 0" https://${BMC_IP}/redfish/v1/Managers/1/LogServices/Actions/public/CollectAllLog
+
+# Wait 60 seconds to Complete
+echo -e "\n Waiting 150 seconds for collect all log ..."
+sleep 150
+
+# Download Onekeylog
+echo -e "\n Step 2. Download Onekeylog"
+curl -k -u $BMC_INFO -X POST -H "Content-Length: 0" https://${BMC_IP}/redfish/v1/Managers/1/LogServices/Actions/public/DownloadAllLog --output $LOG_FILENAME
+
+# Complete
+echo -e "\n Complete Download Onekeylog"

07.bmc_tool_script/Windows_CollectOnekeylog.bat

@@ -0,0 +1,86 @@
+@echo off
+setlocal
+
+:: Param Check
+if "%1"=="" goto :USAGE
+if "%2"=="" goto :USAGE
+if "%3"=="" goto :USAGE
+
+:: ==== Script will start here
+::echo Command Infomation
+::echo BMC_IP: %1
+::echo USER: %2
+::echo PASSWORD: %3
+
+set "BMC_IP=%1"
+set "USER=%2"
+set "PASSWORD=%3"
+
+set "BMC_INFO=%USER%:%PASSWORD%"
+set "redfish_fru_result=%CD%\fru_info.json"
+
+:: Step0. Get BMC SN
+echo __________
+echo Opertion 1 : Check Network Connection with BMC...
+curl -k -u %BMC_INFO% -X GET "https://%BMC_IP%/redfish/v1/Systems/1/public/FRU" > %redfish_fru_result%
+if %ERRORLEVEL% neq 0 (
+	echo Connect to BMC Failed
+	exit /b 1
+)
+
+for /f "delims=" %%a in ('
+	powershell -command "$json = Get-Content -Path '%redfish_fru_result%' -Raw | ConvertFrom-Json; $json.'board'.'Board Serial'"
+') do set "value=%%a"
+set "BoardSN=%value%"
+
+:: Setp1. Get local time stamp
+set "dt=%DATE% %TIME%"
+for /f "tokens=2 delims==" %%a in ('wmic OS get LocalDateTime /value') do set "dt=%%a"
+set "year=%dt:~0,4%"
+set "month=%dt:~4,2%"
+set "day=%dt:~6,2%"
+set "hour=%dt:~8,2%"
+set "minute=%dt:~10,2%"
+set "second=%dt:~12,2%"
+
+set "timestamp=%year%%month%%day%T%hour%%minute%%second%"
+::echo TimeStamp: %timestamp%
+set "LogFile=%CD%\Product_%BoardSN%_%timestamp%.tar.gz"
+
+:: Step2. Post Collect Onekeylog Request to BMC by redfish
+echo __________
+echo Opertion 2 : Post Request to BMC...
+curl -k -u %BMC_INFO% -X POST -H "Content-Length: 0" "https://%BMC_IP%/redfish/v1/Managers/1/LogServices/Actions/public/CollectAllLog"
+
+if %ERRORLEVEL% neq 0 (
+	echo Post Request Error
+	exit /b 1
+)
+
+:: Step3. Wait 150s to Complete Collect
+echo __________
+echo Opertion 3 : Wait 150s for bmc to collect onekeylog...
+timeout /t 150 /nobreak
+
+:: Step4. Download Onekeylog
+echo __________
+echo Opertion 4 : Download onekeylog now ...
+curl -k -u %BMC_INFO% -X POST -H "Content-Length: 0" "https://%BMC_IP%/redfish/v1/Managers/1/LogServices/Actions/public/DownloadAllLog" --output %LogFile%
+
+if %ERRORLEVEL% neq 0 (
+	echo Download Onekeylog Error
+	exit /b 1
+)
+
+:: === Complete
+echo __________
+echo Opertion 5 : Success Download Onekeylog
+echo Onekeylog Path: %LogFile%
+goto :END
+
+:USAGE
+echo Invalid command format
+echo Script Format : CollectOnekeylog.bat [bmc ip] [username] [password]
+
+:END
+endlocal

07.bmc_tool_script/manual_crashdump.sh

@@ -0,0 +1,5 @@
+#!/bin/sh
+
+pid=`ps aux | grep Crashdump | awk 'NR==1{print $2}'`
+kill $pid
+Crashdump --dump-now

07.bmc_tool_script/read_adc_reg.sh

@@ -0,0 +1,114 @@
+#!/bin/sh
+
+# ADC Base Address 0x1e6e 9000
+# Channel0 & Channel 1 0x10
+# Channel2 & Channel 3 0x14
+# Channel4 & Channel 5 0x18
+# Channel6 & Channel 7 0x1c
+# Channel8 & Channel 9 0x20
+# Channel10 & Channel 11 0x24
+# Channel12 & Channel 13 0x28
+# Channel14 & Channel 15 0x2c
+
+#   volt = ((data+1.0) /1024) *1.8; //ADC calculation formular
+#	volt *= resist;        /* based on the hardware resistance added*/
+
+
+Board_Desc="Common_Board"
+Low_Position=0
+High_Position=1
+# ---------------------------------------------------------------
+# Resist List
+# ---------------------------------------------------------------
+Channel00_resist=1
+Channel01_resist=1
+Channel02_resist=1
+Channel03_resist=1
+Channel04_resist=1
+Channel05_resist=1
+Channel06_resist=1
+Channel07_resist=1
+Channel08_resist=1
+Channel09_resist=1
+Channel10_resist=1
+Channel11_resist=1
+Channel12_resist=1
+Channel13_resist=1
+Channel14_resist=1
+Channel15_resist=1
+
+# ---------------------------------------------------------------
+# Channel Name
+# ---------------------------------------------------------------
+Channel00_name="Channel00_Volt"
+Channel01_name="Channel01_Volt"
+Channel02_name="Channel02_Volt"
+Channel03_name="Channel03_Volt"
+Channel04_name="Channel04_Volt"
+Channel05_name="Channel05_Volt"
+Channel06_name="Channel06_Volt"
+Channel07_name="Channel07_Volt"
+Channel08_name="Channel08_Volt"
+Channel09_name="Channel09_Volt"
+Channel10_name="Channel10_Volt"
+Channel11_name="Channel11_Volt"
+Channel12_name="Channel12_Volt"
+Channel13_name="Channel13_Volt"
+Channel14_name="Channel14_Volt"
+Channel15_name="Channel15_Volt"
+
+# ---------------------------------------------------------------
+# Function Define
+# ---------------------------------------------------------------
+# @Param1 ChannelNumber
+# @Param2 ChannelRegOffset
+# @Param3 Pos Flag
+# @Param4 ChannelName
+# @Param5 ChannelResist
+read_channel_and_convert(){
+    RegAddr=0x1e6e90$2
+    # echo "RegAddr=${RegAddr}"
+
+    res=`devmem ${RegAddr} 32`
+    # echo $res
+    if [ $3 = $Low_Position ];then
+        ex=$(echo ${res} | cut -c 8)
+        h=$(echo ${res} | cut -c 9)
+        l=$(echo ${res} | cut -c 10)
+        hex_raw=${ex}${h}${l}
+    else
+        ex=$(echo ${res} | cut -c 4)
+        h=$(echo ${res} | cut -c 5)
+        l=$(echo ${res} | cut -c 6)
+        hex_raw=${ex}${h}${l}
+    fi
+
+    # Convert hex raw data to sensor value
+    dec_raw=$(echo "ibase=16; ${hex_raw}" | bc)
+    volt=$(echo "scale=4; ((${dec_raw} + 1.0) / 1024) * 1.8 * ${5} " | bc)
+    format_volt=$(echo "$volt" | awk '{ if ($0 ~ /^\./) print "0" $0; else print $0 }')
+
+    # Output result
+    echo "Channel$1 | $4 : ${format_volt}V"
+}
+
+# ---------------------------------------------------------------
+# Main
+# ---------------------------------------------------------------
+echo "Board Name : ${Board_Desc}"
+read_channel_and_convert "00" "10" ${Low_Position} "${Channel00_name}" "${Channel00_resist}"
+read_channel_and_convert "01" "10" ${High_Position} "${Channel01_name}" "${Channel01_resist}"
+read_channel_and_convert "02" "14" ${Low_Position} "${Channel02_name}" "${Channel02_resist}"
+read_channel_and_convert "03" "14" ${High_Position} "${Channel03_name}" "${Channel03_resist}"
+read_channel_and_convert "04" "18" ${Low_Position} "${Channel04_name}" "${Channel04_resist}"
+read_channel_and_convert "05" "18" ${High_Position} "${Channel05_name}" "${Channel05_resist}"
+read_channel_and_convert "06" "1c" ${Low_Position} "${Channel06_name}" "${Channel06_resist}"
+read_channel_and_convert "07" "1c" ${High_Position} "${Channel07_name}" "${Channel07_resist}"
+read_channel_and_convert "08" "20" ${Low_Position} "${Channel08_name}" "${Channel08_resist}"
+read_channel_and_convert "09" "20" ${High_Position} "${Channel09_name}" "${Channel09_resist}"
+read_channel_and_convert "10" "24" ${Low_Position} "${Channel10_name}" "${Channel10_resist}"
+read_channel_and_convert "11" "24" ${High_Position} "${Channel11_name}" "${Channel11_resist}"
+read_channel_and_convert "12" "28" ${Low_Position} "${Channel12_name}" "${Channel12_resist}"
+read_channel_and_convert "13" "28" ${High_Position} "${Channel13_name}" "${Channel13_resist}"
+read_channel_and_convert "14" "2c" ${Low_Position} "${Channel14_name}" "${Channel14_resist}"
+read_channel_and_convert "15" "2c" ${High_Position} "${Channel15_name}" "${Channel15_resist}"

Readme.md

@@ -1,19 +1,25 @@
-# 说明
+# 说明
-
+
-## 脚本导航
+## 脚本导航
-### 快速配置脚本环境
+### 快速配置脚本环境
-- 一键安装脚本环境 : [quick_install.sh](./00.quick_install_env/quick_install.sh)
+- 一键安装脚本环境 : [quick_install.sh](./00.quick_install_env/quick_install.sh)
-
+
-### 循环压测类脚本
+### 循环压测类脚本
-- 带内执行power cycle ：[inband_dc_cycle.sh](./01.stress_script/inband_dc_cycle.sh)
+- 带内执行power cycle ：[inband_dc_cycle.sh](./01.stress_script/inband_dc_cycle.sh)
-- 带外执行power cycle : [outband_dc_cycle.sh](./01.stress_script/outband_dc_cycle.sh)
+- 带外执行power cycle : [outband_dc_cycle.sh](./01.stress_script/outband_dc_cycle.sh)
-- 带内执行AC cycle : [inband_ac_cycle.sh](./01.stress_script/inband_ac_cycle.sh)
+- 带内执行AC cycle : [inband_ac_cycle.sh](./01.stress_script/inband_ac_cycle.sh)
-- 带外执行AC cycle : [outband_ac_cycle.sh](./01.stress_script/outband_ac_cycle.sh)
+- 带外执行AC cycle : [outband_ac_cycle.sh](./01.stress_script/outband_ac_cycle.sh)
-- OS执行reboot ：[os_reboot.sh](./01.stress_script/os_reboot.sh)
+- OS执行reboot ：[os_reboot.sh](./01.stress_script/os_reboot.sh)
-- 使用YAFU带内升级BMC ：[inband_stress_update.sh](./01.stress_script/inband_stress_update.sh)
+- 使用YAFU带内升级BMC ：[inband_stress_update.sh](./01.stress_script/inband_stress_update.sh)
-
+
-### nicsensor
+### nicsensor
-- M7服务器BMC读取网卡传感器 ：[nicsensor.sh](./02.nicsensor/nicsensor.sh)
+- M7服务器BMC读取网卡传感器 ：[nicsensor.sh](./02.nicsensor/nicsensor.sh)
-
+
-### 脚本模板
+### 脚本模板
-- 简单的循环模板 ：[template_loop.sh](./03.template/template_loop.sh)
+- 简单的循环模板 ：[template_loop.sh](./03.template/template_loop.sh)
+
+### BMC工具脚本
+- Linux系统下一键收集日志 ：[Linux_CollectOnekeylog.sh](./07.bmc_tool_script/Linux_CollectOnekeylog.sh)
+- Windows系统下一键收集日志 ：[Windows_CollectOnekeylog.bat](./07.bmc_tool_script/Windows_CollectOnekeylog.bat)
+- BMC下快速读取ADC寄存器的数值 ：[read_adc_reg.sh](./07.bmc_tool_script/read_adc_reg.sh)
+- BMC下手动触发Crashdump : [manul_crashdump.sh](./07.bmc_tool_script/manual_crashdump.sh)